- #ASR9K SHOW MAC ADDRESS TABLE HOW TO#
- #ASR9K SHOW MAC ADDRESS TABLE SOFTWARE#
- #ASR9K SHOW MAC ADDRESS TABLE SERIES#
If no IP address is specified, the virtual address is learned from theĪctive router. Specified, that address is used as the designated address for the Hot Standby Useful on interfaces with primary and secondary addresses you can configureĬommand activates HSRP on the configured interface. Indicates that the IP address is a secondary Hot Standby router interface. IP address of the Hot Standby router interface. Group number on the interface for which HSRP is being activated. Must be explicitly configured to turn this feature off.Ĭommand in HSRP interface configuration mode. Minimum delay is applied on all interface up events and the reload delay is That there are no mistaken state changes due to loss of hello packets. Up event to ensure that the interface is ready to pass traffic. Range is 0 to 10000.Ĭommand delays the start of the HSRP finite state machine (FSM) on an interface Reload delay in seconds for first interface up event. Minimum delay in seconds for every interface up event.
This command was replaced with theĪctivation delay for the Hot Standby Router Protocol (HSRP), use theĬommand in HSRP interface configuration mode. HSRP interface configuration Command HistoryĬommand has been deprecated. Group number on the interface to which this authentication string applies. No hsrp authentication Syntax Description To delete an authentication string, use the (applicable for Cisco IOS XR Releases 4.3.x and above) RP/0/ RSP0 /CPU0:router# configure RP/0/ RSP0 /CPU0:router(config)# router hsrp RP/0/ RSP0 /CPU0:router(config-hsrp)# interface tenGigE 0/4/0/4 RP/0/ RSP0 /CPU0:router(config-hsrp-if)# address-family ipv4 RP/0/ RSP0 /CPU0:router(config-hsrp-ipv4)# hsrp 1 version 1 RP/0/ RSP0 /CPU0:router(config-hsrp-gp)# authentication company1 RP/0/ RSP0 /CPU0:router(config-hsrp-gp)#Ĭonfiguration mode. RP/0/ RSP0 /CPU0:router# configure RP/0/ RSP0 /CPU0:router(config)# router hsrp RP/0/ RSP0 /CPU0:router(config-hsrp)# interface tenGigE 0/4/0/4 RP/0/ RSP0 /CPU0:router(config-hsrp-if)# address-family ipv4 RP/0/ RSP0 /CPU0:router(config-hsrp-ipv4)# hsrp 1 RP/0/ RSP0 /CPU0:router(config-hsrp-gp)# authentication company1 RP/0/ RSP0 /CPU0:router(config-hsrp-gp)# (applicable for Cisco IOS XR Releases 4.2.x and below)
#ASR9K SHOW MAC ADDRESS TABLE HOW TO#
This example shows how to configure “company1” as the authentication string required to allow Hot Standby routers in groupġ on tenGigE interface 0/4/0/4 to interoperate: Authentication mismatch prevents a device from learning theĭesignated Hot Standby IP address and the Hot Standby timer values from otherĪuthentication command is available for version 1 groups only Must be configured on all routers and access servers on a LAN to ensure String is sent unencrypted in all HSRP messages. To delete anĪuthentication Syntax DescriptionĪuthentication string. Keyword, the router does not accept the configuration and displays an errorĪuthentication string for the Hot Standby Router Protocol (HSRP), use theĪuthentication command in HSRP group submode. If you configure only the global IPv6 address and commit the changes HSRP for IPv6, you must also configure the linklocal IPv6 address using either HSRP Slave Submode, under the IPv6 address-family Command History Release No address linklocal ipv6-address | autoconfig Syntax Description ipv6-addressĪutoconfigures the HSRP IPv6 link-local address. To deconfigure the virtual link-local IPv6 address for the subordinate group, use theĪddress linklocal ipv6-address | autoconfig Use the address linklocal command in the virtual router submode.
IPv6 address should be enabled and calculated automatically from the virtual router virtual Media Access Control (MAC) address, To either configure the virtual link-local IPv6 address for the subordinate group or to specify that the virtual link-local subordinate secondary virtual IPv4 address.subordinate primary virtual IPv4 address.
#ASR9K SHOW MAC ADDRESS TABLE SERIES#
IP Addresses and Services Configuration Guide for Cisco ASR 9000 Series Routers. Information about HSRP concepts, configuration tasks, and examples, refer to
#ASR9K SHOW MAC ADDRESS TABLE SOFTWARE#
Cisco IOS XR software commands used to configure and monitor the Hot Standby Router
0 kommentar(er)
